Diamonds and Pearls Wedding

Drilling Holes Of Seashells – Making Of Seashell Jewelry

Seashell Jewelry Making

This article will describe some tips and advices how to drill holes of seashells in making of seashells jewelry. Drilling holes of seashells is quite difficult and shall be done very carefully. Seashells are often quite fragile. Be very careful drilling holes in them and also try to pick shells that are not chipping or flaking at the edges. There are a few precautions that we should know and take in order to prevent the seashells from crack and damage.

1 – Drilling bits

Use A Dremel. A Dremel tool works well also because it’s higher speed than your regular drill. Especially good for delicate shells; use a very small bit. It wasn’t possible to use a very fast speed because the hardness of the shell made the drill bit slip and mark the surface. Once the hole was started, continue with slow because even then the drill would overheat from the effort. We had to stop every 5 minutes and allow the drill to cool down for about 20 minutes to half an hour. Also suggested to use diamond points to drill.

2 – Water

When you drill with diamond points, always use water to cool the points or they will fail quickly. This also keeps the dust down, but wear a good quality filter mask or use a vacuume to catch any dust/spray. Seashell dust is toxic, and I don’t mean a little bit toxic. You can really hurt yourself if you breath it in, or get it into your eyes, a cut or sore, or ingest it. Sometimes the particulates are so small you don’t realize they’re in the air around you. When you breathe this dust in, it gets embedded in your lungs and it won’t come out. It will literally be there forever, and it’s toxic. Obviously, don’t put your drill in the water, just the tip of the bit doing the drilling.

3 – Start Drilling

Make sure the drill bit is sharp, and that you are using a high speed drill. Use the smallest drill bit that will accommodate the chain or whatever you’re putting thru the shell. Secure the shell firmly in a vise or other arrangement to make sure it cannot move during the drilling.If the shell is thin, I would suggest putting tape over the spot where you are drilling to help prevent the shell from splintering or cracking.Lay the shell with the top up so that if spintering does occur as the bit reaches the other side, any splintering will be on the bottom (back) of the shell. If you’re not comfortable using a drill, practice first on some scrap shells before drilling in those you want to use.

Now when you start to drill, you’re going to do it like this: hold the drill in a straight up and down position so that the hole will be straight. Hold the drill firmly so that the bit won’t go skidding across the surface of the stone. (Now you know why you need practice pieces.) You’re going to touch the drill bit down semi-firmly, like you mean it, but then lift the drill bit out of the hole so water can pool inside it. Repeat. You can do it pretty quickly, too. Touch down, lift, touch down, lift, etc. When you’re almost all the way though, Stop. Flip your stone over and begin to drill from the other side. This will prevent a “blow out” or chipping the stone or glass where the hole should be. It takes practice to do this, so don’t be hard on yourself. Glass and stone will pretty much drill the same. Anything else may be unpredictable, so a practice piece is necessary.

For more information about Seashells Jewelry Making, visit Jewelry Skills. There are more useful tips and ideas in making of seashells jewelry.

Seashell Jewelry Making

About the Author

The Author from Telok Cempedak Beach Resort, Malaysia

Glass Jewelry Wire Wrapping With Barbara Tilley May 4th @ 8:00PM EST

1.8mm Jewelry Drill Bits – 6 Pack $47.95 Great For Jewelry Making Our fused glass instructors have found these drill bits to be the best for jewelry making. They loved the small size and fine holes they were able to drill in glass with the durable diamond coated tip. A very handy tool for glass jewelry artists. Includes six 1.8 mm drill bits. Attaches easily to a Rotary Tool, such as 67310, Dremel, or standard electric drill using Micro Chuck 76412. Pendants below made by Jen Olsen and Jaime Dobson.

1.1mm Jewelry Drill Bits – 6 Pack $47.95 Great For Jewelry Making Our fused glass instructors have found these drill bits to be the best for jewelry making. They loved the small size and fine holes they were able to drill in glass with the durable diamond coated tip. A very handy tool for glass jewelry artists. Includes six 1.1 mm drill bits. Attaches easily to a Rotary Tool, such as 67310, Dremel, or standard electric drill using Micro Chuck 76412. Pendants below made by Jen Olsen and Jaime Dobson.

2.1mm Jewelry Drill Bits – 6 Pack $47.95 Great For Jewelry Making Our fused glass instructors have found these drill bits to be the best for jewelry making. They loved the small size and fine holes they were able to drill in glass with the durable diamond coated tip. A very handy tool for glass jewelry artists. Includes six 2.1 mm drill bits, the most requested size. Attaches easily to a Rotary Tool, such as 67310, Dremel, or standard electric drill using Micro Chuck 76412. Pendants below made by Jen Olsen and Jaime Dobson.

1.4mm Jewelry Drill Bits – 6 Pack $47.95 Great For Jewelry Making Our fused glass instructors have found these drill bits to be the best for jewelry making. They loved the small size and fine holes they were able to drill in glass with the durable diamond coated tip. A very handy tool for glass jewelry artists. Includes six 1.4 mm drill bits. Attaches easily to a Rotary Tool, such as 67310, Dremel, or standard electric drill using Micro Chuck 76412. Pendants below made by Jen Olsen and Jaime Dobson.

Drill Bits $19.99 Gordon Osmundson Drill Bits – Photographic Print

Twofers Diamond Core Drill Bits – 1/8 $14.95 Two Bits for the Price of One. Aanraku brings you Twofers – superior quality, low-cost grinder and drill bits. Drill holes in your glass with this core drill bit. Great for jewelry making. Fits most electric drills. Coarse 100 diamond mesh grit for quick results.

Micro Jewelry Drill Bit 6-pack $36.95 Great For Jewelry Making Our fused glass instructors have found these drill bits to be the best for jewelry making. They loved the small size and fine holes they were able to drill in glass. A very handy tool for glass jewelry artists. Includes six micro drill bits, three 1.1 mm and three 1.4 mm. Attaches easily to a Rotary Tool, such as 67310, Dremel, or standard electric drill using Micro Chuck 76412. Pendants below made by Jen Olsen and Jaime Dobson.

Advertisement for Drill Bits $39.99 Advertisement for Drill Bits – Giclee Print

12V 17-Piece Set Cordless Drill/Driver w/Case Drill Bits Philips & Flathead Bits $32.97 12V 17-Piece Set Cordless Drill/Driver w/Case Drill Bits Philips & Flathead Bits

Irwin 42934 Forstner Drill Bits $32.16 Irwin 42934 Forstner Drill Bits Irwin 42934 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 2-1/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42922 Forstner Drill Bits $20.03 Irwin 42922 Forstner Drill Bits Irwin 42922 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-3/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42924 Forstner Drill Bits $23.56 Irwin 42924 Forstner Drill Bits Irwin 42924 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-1/2″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42926 Forstner Drill Bits $24.35 Irwin 42926 Forstner Drill Bits Irwin 42926 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-5/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42928 Forstner Drill Bits $25.88 Irwin 42928 Forstner Drill Bits Irwin 42928 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-3/4″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42930 Forstner Drill Bits $26.68 Irwin 42930 Forstner Drill Bits Irwin 42930 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-7/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42932 Forstner Drill Bits $28.4 Irwin 42932 Forstner Drill Bits Irwin 42932 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 2″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42904 Forstner Drill Bits $10.11 Irwin 42904 Forstner Drill Bits Irwin 42904 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1/4″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42906 Forstner Drill Bits $10.11 Irwin 42906 Forstner Drill Bits Irwin 42906 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 3/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42908 Forstner Drill Bits $11.02 Irwin 42908 Forstner Drill Bits Irwin 42908 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1/2″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42910 Forstner Drill Bits $11.89 Irwin 42910 Forstner Drill Bits Irwin 42910 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 5/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42912 Forstner Drill Bits $12.76 Irwin 42912 Forstner Drill Bits Irwin 42912 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 3/4″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42914 Forstner Drill Bits $13.64 Irwin 42914 Forstner Drill Bits Irwin 42914 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 7/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42916 Forstner Drill Bits $15.35 Irwin 42916 Forstner Drill Bits Irwin 42916 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42918 Forstner Drill Bits $16.17 Irwin 42918 Forstner Drill Bits Irwin 42918 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-1/8″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

Irwin 42920 Forstner Drill Bits $17.08 Irwin 42920 Forstner Drill Bits Irwin 42920 Forstner Drill Bits Features: Reduced shank fits 3/8″ and larger drills and drill presses Starts the bit cleanly on uneven surfaces Diameter: 1-1/4″ Shank Size: 3/8″ Bores precision holes at any angle Extra sharp cutting edges drill smooth, flat-bottomed holes Fit 3/8″ drills and drill presses Carded 42904: 1/4″ diameter

DeWALT DW2574 1/4 Rotary Masonry Drill Bits $16.2 DeWalt DW2574 1/4″ Rotary Masonry Drill Bits DeWALT DW2574 1/4″ Rotary Masonry Drill Bits Features: Drill bit For drilling in brick, blocks, or concrete Carbide tip aggressively penetrates surfaces Universal 1/4″ hex shank locking system prevents spinning and slippage 1/4″ diameter Carded

3/8 Glastar Diamond Drill Bit $31.95 Diamond drill bits from Glastar make holes in glass fast. Make openings for clockworks, jewelry and other things. They work with any electric drill and only need water as a lubricant. Each bit drills 50-60 holes. Made with a patented diamond bonding process for extra long life.

1/8 Glastar Diamond Drill Bit $27.95 Diamond drill bits from Glastar make holes in glass fast. Make openings for clockworks, jewelry and other things. They work with almost any electrical drill and only need water as a lubricant. Each bit drills 50-60 holes. Made with a patented diamond bonding process for extra long life.

1/4 Glastar Diamond Drill Bit $27.95 Diamond drill bits from Glastar make holes in glass fast. Make openings for clockworks, jewelry and other things. They work with any electric drill and only need water as a lubricant. Each bit drills 50-60 holes. Made with a patented diamond bonding process for extra long life.

Drill Bit(Pack of 48) $1.99 5 piece masonry drill bits.

Vermont American 14615 Brad Point Drill Bits $24.66 Vermont American 14615 Brad Point Drill Bits Brad point drill bits are designed to drill smooth, clean cuts in wood. The brand point tip provides easy positioning and accurate starts. Extra-wide flutes yield fast chip removal. Vermont American 14615 Brad Point Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

1/8” Stubby Double Ended Drill Bits – 12 Pack $6.95 ? Special body panel drill bits for use in autobody repair.By Astro Pneumatic.

Vermont American 12648 Cobalt Drill Bits $8.38 Vermont American 12648 Cobalt Drill Bits Cobalt drill bits offer the best heat resistance for drilling in extremely hard and abrasive materials including stainless steel, titanium and cast iron Vermont American 12648 Cobalt Drill Bits Features: The 135-degree split point ensures a fast start with no walking or skating Bits sizes smaller than 1/8″ have 118-degree standard point Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 12649 Cobalt Drill Bits $12.05 Vermont American 12649 Cobalt Drill Bits Cobalt drill bits offer the best heat resistance for drilling in extremely hard and abrasive materials including stainless steel, titanium and cast iron Vermont American 12649 Cobalt Drill Bits Features: The 135-degree split point ensures a fast start with no walking or skating Bits sizes smaller than 1/8″ have 118-degree standard point Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 12650 Cobalt Drill Bits $19.04 Vermont American 12650 Cobalt Drill Bits Cobalt drill bits offer the best heat resistance for drilling in extremely hard and abrasive materials including stainless steel, titanium and cast iron Vermont American 12650 Cobalt Drill Bits Features: The 135-degree split point ensures a fast start with no walking or skating Bits sizes smaller than 1/8″ have 118-degree standard point Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Dremel 628 Assorted Drill Bits 7 Piece Set $5.76 Dremel 628 Assorted Drill Bits 7 Piece Set Dremel 628 Assorted Drill Bits 7 Piece Set Features: A set of seven high-speed drill bits made from high-grade steel Ideal for drilling into soft materials Made of high speed steel Ideal for all moto-tools, cordless tools, and flex-shaft tools Includes 1/32″ and 3/64″ Drill Bits for use with collet #483 (2615-4153), 1/16″ and 5/64″ Drill Bits for use with collet #482 (2615-4138), 3/32″ and 7/64″ Drill Bits for use with collet #481 (2615-4120), and 1/8″ and larger Drill Bits for use with collet #480 (2615-4112) Carded

Vermont American 12338 Titanium Coated Drill Bits $15.68 Vermont American 12338 Titanium Coated Drill Bits Titanium drill bits offer the best durability and speed for repetitive drilling applications in steel, alloy steel, wood and plastic. The titanium coating lasts six times longer than standard high speed steel drill bits. Vermont American 12338 Titanium Coated Drill Bits Features: Each bit features a 135-degree split point for fast starts and minimal walking or skating. Bit sizes under 1/8″ and 3.5 mm have a 118-degree standard point configuration Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 12339 Titanium Coated Drill Bits $23.7 Vermont American 12339 Titanium Coated Drill Bits Titanium drill bits offer the best durability and speed for repetitive drilling applications in steel, alloy steel, wood and plastic. The titanium coating lasts six times longer than standard high speed steel drill bits. Vermont American 12339 Titanium Coated Drill Bits Features: Each bit features a 135-degree split point for fast starts and minimal walking or skating. Bit sizes under 1/8″ and 3.5 mm have a 118-degree standard point configuration Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 12340 Titanium Coated Drill Bits $17.19 Vermont American 12340 Titanium Coated Drill Bits Titanium drill bits offer the best durability and speed for repetitive drilling applications in steel, alloy steel, wood and plastic. The titanium coating lasts six times longer than standard high speed steel drill bits. Vermont American 12340 Titanium Coated Drill Bits Features: Each bit features a 135-degree split point for fast starts and minimal walking or skating. Bit sizes under 1/8″ and 3.5 mm have a 118-degree standard point configuration Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Skil 97009 Masonry Drill Bits (9 pc) $9.77 Skil 97009 Masonry Drill Bits (9 pc) Founded in 1924 as the Michel Electric Handsaw Company and renamed Skilsaw, Inc. in 1926, SKIL has become one of the most recognized and powerful brands in the power tool industry. From circular saws and jigsaws to sanders and drills, SKIL power tools are engineered to deliver the high-performance and durability that today’s growing population of Do-It-Yourselfers demand. Skil 97009 Masonry Drill Bits (9 pc) Features: includes bit sizes 1/8″ (2 bits), 5/32″, 3/16″ (2 bits), 5/16″ and 3/8 plastic case for convenient tool box storage

Mibro 456831 4 Piece Set Glass & Tile Drill Bits $13.97 Mibro 456831 4 Piece Set Glass & Tile Drill Bits Mibro 456831 4 Piece Set Glass & Tile Drill Bits Features: Carbide tipped drill set 4 piece set Includes 1/8″, 3/16″, 1/4″, and 5/16″ bits Carded

Blum Inc. M31.1000 Eco Drill and Drill Bits with Variable Boring Distance from 2mm to 8mm $342.33 Blum Inc. M31.1000 Eco Drill and Drill Bits with Variable Boring Distance from 2mm to 8mm Blum Inc. M31.1000 Eco Drill and Drill Bits with Variable Boring Distance from 2mm to 8mm Features: Each drill bit is driven separately and retracts automatically. Includes drill bits and two Torx driver bits. Simple device for boring Blum hinge pattern. Requires 14v or better drill.

Vermont American 14200 SDS-plus Masonry Drill Bits $4.62 Vermont American 14200 SDS-plus Masonry Drill Bits Vermont American 14200 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14202 SDS-plus Masonry Drill Bits $3.06 Vermont American 14202 SDS-plus Masonry Drill Bits Vermont American 14202 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14208 SDS-plus Masonry Drill Bits $3.01 Vermont American 14208 SDS-plus Masonry Drill Bits Vermont American 14208 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14211 SDS-plus Masonry Drill Bits $4.29 Vermont American 14211 SDS-plus Masonry Drill Bits Vermont American 14211 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14213 SDS-plus Masonry Drill Bits $4.02 Vermont American 14213 SDS-plus Masonry Drill Bits Vermont American 14213 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14215 SDS-plus Masonry Drill Bits $7.58 Vermont American 14215 SDS-plus Masonry Drill Bits Vermont American 14215 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14219 SDS-plus Masonry Drill Bits $5.02 Vermont American 14219 SDS-plus Masonry Drill Bits Vermont American 14219 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14221 SDS-plus Masonry Drill Bits $9.07 Vermont American 14221 SDS-plus Masonry Drill Bits Vermont American 14221 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14225 SDS-plus Masonry Drill Bits $9.41 Vermont American 14225 SDS-plus Masonry Drill Bits Vermont American 14225 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14226 SDS-plus Masonry Drill Bits $15 Vermont American 14226 SDS-plus Masonry Drill Bits Vermont American 14226 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14229 SDS-plus Masonry Drill Bits $16.31 Vermont American 14229 SDS-plus Masonry Drill Bits Vermont American 14229 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14230 SDS-plus Masonry Drill Bits $16.51 Vermont American 14230 SDS-plus Masonry Drill Bits Vermont American 14230 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14237 SDS-plus Masonry Drill Bits $24.46 Vermont American 14237 SDS-plus Masonry Drill Bits Vermont American 14237 SDS-plus Masonry Drill Bits Features: Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 14376 Concrete Screw Drill Bits $16.25 Vermont American 14376 Concrete Screw Drill Bits Vermont American 14376 Concrete Screw Drill Bits Features: Specially-designed carbide tip provides optimum pilot hole sizes for 3/16″ and 1/4″ Tapcon concrete Hardened steel body provides strength and long life Special shank tang fits Tapcon installation tools 3″ flute length 5/32″ shank 4-1/2″ overall length Carded 14375: 5/32″ diameter 14376: 3/16″ diameter

Vermont American 14375 Concrete Screw Drill Bits $15 Vermont American 14375 Concrete Screw Drill Bits Vermont American 14375 Concrete Screw Drill Bits Features: Specially-designed carbide tip provides optimum pilot hole sizes for 3/16″ and 1/4″ Tapcon concrete Hardened steel body provides strength and long life Special shank tang fits Tapcon installation tools 3″ flute length 5/32″ shank 4-1/2″ overall length Carded 14375: 5/32″ diameter 14376: 3/16″ diameter

Petzl RocPec Drill Bit $47.95 10mm and 12mm drill bits for RocPecFeatures:10mm or 12mm

Vermont American 12374 Titanium Coated Drill Bits $22.5 Vermont American 12374 Titanium Coated Drill Bits Vermont American 12374 Titanium Coated Drill Bits Features: Titanium coated for 6 times longer life than standard high speed steel drill bits For repetitive drilling in steel, alloy steels, wood, and plastic Ideal for contractors, serious Do-It-Yourselfers, machine shops, and mechanics 135º split point starts fast and prevents drill walking Carded 12354: 1/16″ diameter, 7/8″ flute length, 1-7/8″ overall length 12355: 5/64″ diameter, 1″ flute length, 2″ overall length 12356: 3/32″ diameter, 1-1/4″ flute length, 2-1/4″ overall length 12357: 7/64″ diameter, 1-1/2″ flute length, 2-5/8″ overall length 12358: 1/8″ diameter, 1-5/8″ flute length, 2-3/4″ overall length

Kobalt 5pk. 1/2 Masonry Drill Bits(Pack of 5) $16.49 Kobalt 5pk. 1/2″ Masonry Drill Bits. 6″ Overall Length. Packaged as shown.

Vermont American 11836 Wire Gauge Drill Bits $5 Vermont American 11836 Wire Gauge Drill Bits Vermont American 11836 Wire Gauge Drill Bits Features: For drilling in wood, metal, and plastic For precision hole sizing such as tapping threaded holes Wire gauge diameters fall between standard fractional sizes for precise hole sizes Popular taps through 1/4-28 require the use of wire gauge drill bits 118º point for general-purpose drilling 1/4″ shank Carded 11807: No 7 wire gauge, 2-7/16″ flute length, 3-5/8″ overall length 11821: No 21 wire gauge, 2-1/8″ flute length, 3-1/4″ overall length 11825: No 25 wire gauge, 1-7/8″ flute length, 3″ overall length

Vermont American 11807 Wire Gauge Drill Bits $7.5 Vermont American 11807 Wire Gauge Drill Bits Vermont American 11807 Wire Gauge Drill Bits Features: For drilling in wood, metal, and plastic For precision hole sizing such as tapping threaded holes Wire gauge diameters fall between standard fractional sizes for precise hole sizes Popular taps through 1/4-28 require the use of wire gauge drill bits 118º point for general-purpose drilling 1/4″ shank Carded 11807: No 7 wire gauge, 2-7/16″ flute length, 3-5/8″ overall length 11821: No 21 wire gauge, 2-1/8″ flute length, 3-1/4″ overall length 11825: No 25 wire gauge, 1-7/8″ flute length, 3″ overall length

Vermont American 11844 Wire Gauge Drill Bits $5 Vermont American 11844 Wire Gauge Drill Bits Vermont American 11844 Wire Gauge Drill Bits Features: For drilling in wood, metal, and plastic For precision hole sizing such as tapping threaded holes Wire gauge diameters fall between standard fractional sizes for precise hole sizes Popular taps through 1/4-28 require the use of wire gauge drill bits 118º point for general-purpose drilling 1/4″ shank Carded 11807: No 7 wire gauge, 2-7/16″ flute length, 3-5/8″ overall length 11821: No 21 wire gauge, 2-1/8″ flute length, 3-1/4″ overall length 11825: No 25 wire gauge, 1-7/8″ flute length, 3″ overall length

Vermont American 13305 Glass & Tile Drill Bits $32.5 Vermont American 13305 Glass & Tile Drill Bits Vermont American 13305 Glass & Tile Drill Bits Features: Smooth accurate drilling in glass, tile, marble, china, and mirrors Spear-pointed tip design reduces breakout Ideal for drilling fastener holes in bathroom tile or wall mirrors Carbide-tipped for long life Fits drills with 3/8″ or larger chucks Carded 13301: 1/8″ diameter, 2-1/4″ overall length, 1000 max rpm 13303: 3/16″ diameter, 2-1/4″ overall length, 750 max rpm 13304: 1/4″ diameter, 2-1/4″ overall length, 500 max rpm 13305: 5/16″ diameter, 2-7/8″ overall length, 400 max rpm

Vermont American 13304 Glass & Tile Drill Bits $25 Vermont American 13304 Glass & Tile Drill Bits Vermont American 13304 Glass & Tile Drill Bits Features: Smooth accurate drilling in glass, tile, marble, china, and mirrors Spear-pointed tip design reduces breakout Ideal for drilling fastener holes in bathroom tile or wall mirrors Carbide-tipped for long life Fits drills with 3/8″ or larger chucks Carded 13301: 1/8″ diameter, 2-1/4″ overall length, 1000 max rpm 13303: 3/16″ diameter, 2-1/4″ overall length, 750 max rpm 13304: 1/4″ diameter, 2-1/4″ overall length, 500 max rpm 13305: 5/16″ diameter, 2-7/8″ overall length, 400 max rpm

Vermont American 13301 Glass & Tile Drill Bits $22.5 Vermont American 13301 Glass & Tile Drill Bits Vermont American 13301 Glass & Tile Drill Bits Features: Smooth accurate drilling in glass, tile, marble, china, and mirrors Spear-pointed tip design reduces breakout Ideal for drilling fastener holes in bathroom tile or wall mirrors Carbide-tipped for long life Fits drills with 3/8″ or larger chucks Carded 13301: 1/8″ diameter, 2-1/4″ overall length, 1000 max rpm 13303: 3/16″ diameter, 2-1/4″ overall length, 750 max rpm 13304: 1/4″ diameter, 2-1/4″ overall length, 500 max rpm 13305: 5/16″ diameter, 2-7/8″ overall length, 400 max rpm

Vermont American 13307 Glass & Tile Drill Bits $57.5 Vermont American 13307 Glass & Tile Drill Bits Vermont American 13307 Glass & Tile Drill Bits Features: Smooth accurate drilling in glass, tile, marble, china, and mirrors Spear-pointed tip design reduces breakout Ideal for drilling fastener holes in bathroom tile or wall mirrors Carbide-tipped for long life Fits drills with 3/8″ or larger chucks Carded 13301: 1/8″ diameter, 2-1/4″ overall length, 1000 max rpm 13303: 3/16″ diameter, 2-1/4″ overall length, 750 max rpm 13304: 1/4″ diameter, 2-1/4″ overall length, 500 max rpm 13305: 5/16″ diameter, 2-7/8″ overall length, 400 max rpm

Vermont American 13131 Hex Shank Drill Bits $12.5 Vermont American 13131 Hex Shank Drill Bits Vermont American 13131 Hex Shank Drill Bits Features: Designed for drilling in wood, metal, and plastic Fits cordless drills, cordless screwdrivers, and quick change adapters 1/4″ hex shanks for quick bit changes Hardened and tempered for long life 13126: 3/32″ diameter, carded 13127: 7/64″ diameter, carded 13128: 1/8″ diameter, carded 13129: 9/64″ diameter, 2 per card 13130: 5/32″ diameter, 2 per card 13131: 3/16″ diameter, 2 per card

Vermont American 13133 Hex Shank Drill Bits $20 Vermont American 13133 Hex Shank Drill Bits Vermont American 13133 Hex Shank Drill Bits Features: Designed for drilling in wood, metal, and plastic Fits cordless drills, cordless screwdrivers, and quick change adapters 1/4″ hex shanks for quick bit changes Hardened and tempered for long life 13126: 3/32″ diameter, carded 13127: 7/64″ diameter, carded 13128: 1/8″ diameter, carded 13129: 9/64″ diameter, 2 per card 13130: 5/32″ diameter, 2 per card 13131: 3/16″ diameter, 2 per card

Inland 3/4 Core Drill Bit $60.95 3/4 (19 mm) Core Drill Bit. Inland diamond coated core drill bits come in numerous diameters and are indispensable for drilling holes in a wide range of materials. Key Features 3/8 (10 mm) shaft fits most hand drills and drill presses. Drill 3/4 diameter holes Use on glass, ceramic tile, porcelain, stone, marble, plastics and fiberglass. Ejection port to easily remove stuck plugs if they occur. Product Uses Make holes in clock faces for clock works. Drill holes for drains in ceramic tile and stone work installations. Drill holes for plumbing lines and fixtures in ceramic tile and stone work installations. Create small holes for hanging. Make holes for eyes in glass projects. Make axle holes for kaleidoscope image wheels. Make holes for hanging jewelry. Drill in composite counter tops for plumbing fixtures. Drill in fiberglass boats for accessory and fixture installations. Cut out for outlets on mirrored walls. Cut holes for hardware on glass doors. Image shown of Core Drill Bit Group courtesy of Inland.

Inland 5/8 Core Drill Bit $56.95 5/8 (16 mm) Core Drill Bit. Inland diamond coated core drill bits come in numerous diameters and are indispensable for drilling holes in a wide range of materials. Key Features 3/8 (10 mm) shaft fits most hand drills and drill presses. Drill 5/8 diameter holes Use on glass, ceramic tile, porcelain, stone, marble, plastics and fiberglass. Ejection port to easily remove stuck plugs if they occur. Product Uses Make holes in clock faces for clock works. Drill holes for drains in ceramic tile and stone work installations. Drill holes for plumbing lines and fixtures in ceramic tile and stone work installations. Create small holes for hanging. Make holes for eyes in glass projects. Make axle holes for kaleidoscope image wheels. Make holes for hanging jewelry. Drill in composite counter tops for plumbing fixtures. Drill in fiberglass boats for accessory and fixture installations. Cut out for outlets on mirrored walls. Cut holes for hardware on glass doors. Image of Core Drill Bit Group courtesy of Inland.

Inland 7/8 Core Drill Bit $66.95 7/8 (22 mm) Core Drill Bit. Inland diamond coated core drill bits come in numerous diameters and are indispensable for drilling holes in a wide range of materials. Key Features 3/8 (10 mm) shaft fits most hand drills and drill presses. Drill 7/8 diameter holes Use on glass, ceramic tile, porcelain, stone, marble, plastics and fiberglass. Ejection port to easily remove stuck plugs if they occur. Product Uses Make holes in clock faces for clock works. Drill holes for drains in ceramic tile and stone work installations. Drill holes for plumbing lines and fixtures in ceramic tile and stone work installations. Create small holes for hanging. Make holes for eyes in glass projects. Make axle holes for kaleidoscope image wheels. Make holes for hanging jewelry. Drill in composite counter tops for plumbing fixtures. Drill in fiberglass boats for accessory and fixture installations. Cut out for outlets on mirrored walls. Cut holes for hardware on glass doors. Image shown of Core Drill Bit Group courtesy of Inland.

Inland 1 Core Drill Bit $64.95 1 (25.4 mm) Core Drill Bit. Inland diamond coated core drill bits come in numerous diameters and are indispensable for drilling holes in a wide range of materials. Key Features 3/8 (10 mm) shaft fits most hand drills and drill presses. Drill 1 diameter holes Use on glass, ceramic tile, porcelain, stone, marble, plastics and fiberglass. Ejection port to easily remove stuck plugs if they occur. Product Uses Make holes in clock faces for clock works. Drill holes for drains in ceramic tile and stone work installations. Drill holes for plumbing lines and fixtures in ceramic tile and stone work installations. Create small holes for hanging. Make holes for eyes in glass projects. Make axle holes for kaleidoscope image wheels. Make holes for hanging jewelry. Drill in composite counter tops for plumbing fixtures. Drill in fiberglass boats for accessory and fixture installations. Cut out for outlets on mirrored walls. Cut holes for hardware on glass doors. Image shown of Core Drill Bit Group courtesy of Inland.

Vermont American 13484 High Speed Steel Left-hand Drill Bits $25.13 Vermont American 13484 High Speed Steel Left-hand Drill Bits Left-hand drill bits are ideal for extracting broken, right-hand threaded studs and bolts. Designed for use in reversible drills, lathes and milling machines. Vermont American 13484 High Speed Steel Left-hand Drill Bits Features: Bits feature a 135-degree split point to minimize bit walking or skating Diameter: 1/4″ Quantity: 5, 1 per card

Vermont American 12679 Cobalt Drill Bits (3 Pack) $27.98 Vermont American 12679 Cobalt Drill Bits (3 Pack) Cobalt drill bits offer the best heat resistance for drilling in extremely hard and abrasive materials including stainless steel, titanium and cast iron Vermont American 12679 Cobalt Drill Bits (3 Pack) Features: Features a 135-degree split point for fast starts and minimal walking or skating Stubby length drill bits are ideal for drilling in sheet metal. The shorter length increases rigidity and reduces breakage Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 12654 Industrial Cobalt Drill Bits $11.25 Vermont American 12654 Industrial Cobalt Drill Bits Vermont American 12654 Industrial Cobalt Drill Bits Features: Designed for drilling stainless steel and other abrasive materials Designed to withstand high drilling heat 135º split point starts fast and prevents drill walking Ideal for contractors, maintenance, machine shops, and garages 1/4″ shank 12654: 1/16″ diameter, 7/8″ flute length, 1-7/8″ overall length 12656: 3/32″ diameter, 1-1/4″ flute length, 2-1/4″ overall length 12657: 7/64″ diameter, 1-1/2″ flute length, 2-5/8″ overall length 12658: 1/8″ diameter, 1-5/8″ flute length, 2-3/4″ overall length 12659: 9/64″ diameter, 1-3/4″ flute length, 2-7/8″ overall length

Vermont American 12670 Industrial Cobalt Drill Bits $13.75 Vermont American 12670 Industrial Cobalt Drill Bits Vermont American 12670 Industrial Cobalt Drill Bits Features: Designed for drilling stainless steel and other abrasive materials Designed to withstand high drilling heat 135º split point starts fast and prevents drill walking Ideal for contractors, maintenance, machine shops, and garages 1/4″ shank 12654: 1/16″ diameter, 7/8″ flute length, 1-7/8″ overall length 12656: 3/32″ diameter, 1-1/4″ flute length, 2-1/4″ overall length 12657: 7/64″ diameter, 1-1/2″ flute length, 2-5/8″ overall length 12658: 1/8″ diameter, 1-5/8″ flute length, 2-3/4″ overall length 12659: 9/64″ diameter, 1-3/4″ flute length, 2-7/8″ overall length

Vermont American 11808 Black Oxide Wire Gauge Drill Bits $1.61 Vermont American 11808 Black Oxide Wire Gauge Drill Bits Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Vermont American 11808 Black Oxide Wire Gauge Drill Bits Features: Bits feature a 135-degree split point that starts fast and minimizes bit walking or skating. Bits smaller than 1/8″ have 118-degree standard point. Bits larger than 3/8″ diameter have reduced shank for use in 3/8″ drills. Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Inland 1-1/16 Core Drill Bit $78.95 1-1/16 (27 mm) Core Drill Bit. Inland diamond coated core drills bits come in numerous diameters and are indispensable for drilling holes in a wide range of materials. Key Features 3/8 (10 mm) shaft fits most hand drills and drill presses. Drill 1-1/16 diameter holes Use on glass, ceramic tile, porcelain, stone, marble, plastics and fiberglass. Ejection port to easily remove stuck plugs if they occur. Product Uses Make holes in clock faces for clock works. Drill holes for drains in ceramic tile and stone work installations. Drill holes for plumbing lines and fixtures in ceramic tile and stone work installations. Create small holes for hanging. Make holes for eyes in glass projects. Make axle holes for kaleidoscope image wheels. Make holes for hanging jewelry. Drill in composite counter tops for plumbing fixtures. Drill in fiberglass boats for accessory and fixture installations. Cut out for outlets on mirrored walls. Cut holes for hardware on glass doors. Image shown of Core Drill Bit Group courtesy of Inland.

High Speed Drill Bits 1/16 (.0625)(Pack of 24) $1.99 High Speed Drill Bits 1/16″ (.0625″) High Speed Drill Bits Size: 1/16″ (.0625″) 2 Pieces For general purpose drilling in metal wood and plastic.

Vermont American 12672 Cobalt Drill Bits (3 Pack) $17.96 Vermont American 12672 Cobalt Drill Bits (3 Pack) Cobalt drill bits offer the best heat resistance for drilling in extremely hard and abrasive materials including stainless steel, titanium and cast iron Vermont American 12672 Cobalt Drill Bits (3 Pack) Features: The 135-degree split point ensures a fast start with no walking or skating Bits sizes smaller than 1/8″ have 118-degree standard point Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 10562 High Speed Steel Drill Bits with Reduced Shank $30.26 Vermont American 10562 High Speed Steel Drill Bits with Reduced Shank For drilling in wood, metal and plastic. Each high speed steel bit is hardened and tempered for long life and high performance in tough applications. Vermont American 10562 High Speed Steel Drill Bits with Reduced Shank Features: Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 1/2″ Flute Length:4-1/2″ Overall Length: 6″ Quantity: 10, 1 per card Bulk Item#: 10132 Bulk Quantity: 3 bits in bag

Vermont American 12511 25/64 Titanium Coated Drill Bits With Reduced Shank $32.5 Vermont American 12511 25/64″ Titanium Coated Drill Bits With Reduced Shank Vermont American 12511 25/64″ Titanium Coated Drill Bits With Reduced Shank Features: Titanium drill bits offer the best durability and speed for repetitive drilling applications Ideal for use on steel, alloy steel, wood, and plastic Coating lasts six times longer than standard high speed steel drill bits Features a 135º split point that starts fast and minimizes bit walking or skating 25/64″ diameter 3-3/4″ flute length 5-1/8″ overall length 3/8″ shank diameter Carded

Vermont American 11801 Black Oxide Wire Gauge Drill Bits $2 Vermont American 11801 Black Oxide Wire Gauge Drill Bits Vermont American 11801 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 1 Flute Length: 2-5/8″ Overall Length: 3-7/8″ Quantity: 5, 1 per card

Vermont American 11831 Black Oxide Wire Gauge Drill Bits $1 Vermont American 11831 Black Oxide Wire Gauge Drill Bits Vermont American 11831 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 31 Flute Length: 1-5/8″ Overall Length: 2-3/4″ Quantity: 5, 1 per card

Vermont American 11802 Black Oxide Wire Gauge Drill Bits $2 Vermont American 11802 Black Oxide Wire Gauge Drill Bits Vermont American 11802 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 2 Flute Length: 2-5/8″ Overall Length: 3-7/8″ Quantity: 5, 1 per card

Vermont American 11804 Black Oxide Wire Gauge Drill Bits $2 Vermont American 11804 Black Oxide Wire Gauge Drill Bits Vermont American 11804 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 4 Flute Length: 2-1/2″ Overall Length: 3-3/4″ Quantity: 5, 1 per card

Vermont American 11806 Black Oxide Wire Gauge Drill Bits $2 Vermont American 11806 Black Oxide Wire Gauge Drill Bits Vermont American 11806 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 6 Flute Length: 2-1/2″ Overall Length: 3-3/4″ Quantity: 5, 1 per card

Vermont American 11805 Black Oxide Wire Gauge Drill Bits $2 Vermont American 11805 Black Oxide Wire Gauge Drill Bits Vermont American 11805 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 5 Flute Length: 2-1/2″ Overall Length: 3-3/4″ Quantity: 5, 1 per card

Vermont American 11803 Black Oxide Wire Gauge Drill Bits $2 Vermont American 11803 Black Oxide Wire Gauge Drill Bits Vermont American 11803 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 3 Flute Length: 2-1/2″ Overall Length: 3-3/4″ Quantity: 5, 1 per card

Vermont American 11814 Black Oxide Wire Gauge Drill Bits $1.58 Vermont American 11814 Black Oxide Wire Gauge Drill Bits Vermont American 11814 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 14 Flute Length: 2-3/16″ Overall Length: 3-3/8″ Quantity: 5, 1 per card

Vermont American 11812 Black Oxide Wire Gauge Drill Bits $1.61 Vermont American 11812 Black Oxide Wire Gauge Drill Bits Vermont American 11812 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 12 Flute Length: 2-5/16″ Overall Length: 3-1/2″ Quantity: 5, 1 per card

Vermont American 11828 Black Oxide Wire Gauge Drill Bits $1.2 Vermont American 11828 Black Oxide Wire Gauge Drill Bits Vermont American 11828 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 28 Flute Length: 1-3/4″ Overall Length: 2-7/8″ Quantity: 5, 1 per card

Vermont American 11822 Black Oxide Wire Gauge Drill Bits $1.31 Vermont American 11822 Black Oxide Wire Gauge Drill Bits Vermont American 11822 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 22 Flute Length: 2″ Overall Length: 3-1/8″ Quantity: 5, 1 per card

Vermont American 11824 Black Oxide Wire Gauge Drill Bits $1.31 Vermont American 11824 Black Oxide Wire Gauge Drill Bits Vermont American 11824 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 24 Flute Length: 2″ Overall Length: 3-1/8″ Quantity: 5, 1 per card

Vermont American 11823 Black Oxide Wire Gauge Drill Bits $1.31 Vermont American 11823 Black Oxide Wire Gauge Drill Bits Vermont American 11823 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 23 Flute Length: 2″ Overall Length: 3-1/8″ Quantity: 5, 1 per card

Vermont American 11815 Black Oxide Wire Gauge Drill Bits $1.58 Vermont American 11815 Black Oxide Wire Gauge Drill Bits Vermont American 11815 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 15 Flute Length: 2-3/16″ Overall Length: 3-3/8″ Quantity: 5, 1 per card

Vermont American 11818 Black Oxide Wire Gauge Drill Bits $1.38 Vermont American 11818 Black Oxide Wire Gauge Drill Bits Vermont American 11818 Black Oxide Wire Gauge Drill Bits Features: Wire gauge drill bits are used in wood, metal and plastic applications where more precisely sized holes are required. The bits drill an exact hole size, making them ideal for tapping. Bit diameters fall between standard fractional sizes. Each drill bit features a 118-degree standard point configuration for general purpose drilling applications Popular taps up to 1/4-24 require use of wire gauge drill bits Diameter: 18 Flute Length: 2-1/8″ Overall Length: 3-1/4″ Quantity: 5, 1 per card